Hazardous Area Fluorescent Light Fixture - Class 1 Division 2 Groups A, B, C and D - UL 1598A Listed and CUL listed for Canada.
Our standard hazardous location fluorescent lights are multi-voltage with standard surface end mount. Class 1 Division II fixtures are appropriate for open air areas that have the occasional presence of flammable petrochemical vapors. Typically, these lights are used in hazardous location areas that are adjacent to an area where those vapors are present all the time (where Class 1, Division 1 rated lights are required).
HAL-48-2L Hazardous Area Light - Class 1 Division 2 - Video Animation - Standard Mount
2 DAY LEAD TIME ON THIS ITEM. FREE SHIPPING.
Made in the USA



1. Each unit dialectically tested.
2. Fixture arrives assembled to reduce installation time and cost.
3. Fixture constructed of extruded corrosion resistant copper free aluminum alloy
4. Heavy gauge extruded aluminum reflectors (2.5 mm thick) with high gloss reflective finish. Resists dents and corrosion.
5. Relamping done via 4 turn latches, which enable the operator to unlatch the hinged door and access the lamps.
6. 3/4 inch, threaded access hole for wiring conduit.
7. Units can be wired end to end in series.
UL Ratings:
a. Class 1 Division 2, Groups A, B, C and D
b. UL 595 Outdoor Marine Type (Saltwater)
c. UL 1598A Marine Type
Temperature Rating - T4C
ALSO C UL LISTED. UL Certified for Canadian Safety Approval Standards.
Click here to learn more about National Electrical Code Hazardous Location Classifications
Dimensions:
49 3/4 inches length X 7 inches width X 6 1/8 inches tall
Weight: 33 pounds

Click here for a dimensional drawing on this Class 1 Division 2 Fluorescent Fixture
Click here to download the spec sheet for the HAL-48-2L Hazardous Location Light
The HAL-48-2L has an electronic multi-voltage ballast and works on the following voltages:
120 Volt 60 HZ
220 Volt 50 HZ
240 Volt 60 HZ
277 Volts 60 HZ
Wiring Hub Size
• 3/4 inch threaded
Lamp Features:
Our most popular standard lamp configuration uses 60 Watt High Output T-12 fluorescent lamps producing 4050 lumens per lamp (8100 lumens total). However, we do have options, including:
F54-T5/841/HO – 54 Watt, 5000 lumens per bulb, 20,000 hours life, 4100 Kelvin color
F48-T12/HO – 4050 lumens per bulb, 12,000 hours life, 4100 Kelvin color
F32-T8/841 – 2950 lumens per bulb, 24,000 hours life, 4100 Kelvin color
Twist access latches then enables the operator to open the hinged access glass door and change the bulbs.


Standard Bracket Mounts:
Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg.
Mounting brackets are removable. A single through hole enables the operator to install the light to any surface.

The mounting bracket attached to one end of the fluorescent light fixture.

The mounting bracket attached to the other end of the fluorescent light fixture. 3/4 inch threaded hole for wiring and conduit access.

Applications include:
• Aircraft maintenance
• Oil drilling rigs
• Refineries
• Solvent and cleaning areas
• Gas processing plants
• Chemical manufacturing
• Waste treatment plants
• Gas processing plants
Replacement bulb for our standard fixture is F48-T12-HO, which can be found wherever fluorescent lamps are sold in your local area.